3-axle POWER LINE sliding tarpaulin platform semitrailer – coil

• Product details

  TYPE DESIGNATION

  3-AXLE POWER LINE SLIDING TARPAULIN PLATFORM SEMITRAILER RH1 5 0 – COIL

  WEIGHTS

  Gross train weight (perm.): 40 t
  Gross weight (techn.): 39 t
  Axle assembly load (techn.): 27 t
  Fifth-wheel load (techn.): 12 t
  Tare weight: approx. 6 t

  DIMENSIONS

  Internal platform length: approx. 13,620 mm
  Internal platform width: approx. 2,480 mm
  Total width: 2,550 mm
  Load space internal height: approx. 2,720 mm
  Lateral loading height below guide rail: approx. 2,620 mm
  Internal width between guide rails: approx. 2,430 mm
  Portal loading height: approx. 2,620 mm
  Portal loading width: approx. 2,480 mm
  Loading height: approx. 1 5 0 mm over fifth-wheel height

  FRAME

  Welded steel frame construction – lightweight design
  Reinforced for point loading = coil transport (27 t at centre of gravity across min. 2,000 mm length)
  Frame for unladen fifth-wheel height of 1,120 – 1, 19 0 mm with air-sprung STT
  Replaceable 2″ kingpin (EC installation dimension,
  width across corners: 2,040 mm)
  Perforated external frame with approx. 100 mm hole spacing, 40/25 mm slot according to DIN EN 12640 and 21 pairs of recessed 2.5 t lashing points/rings, and an additional 5 pairs of 4 t lashing points in the recess area on the external frame

  CHASSIS

  Air suspension with lifting and lowering device (approx. +120/-80 mm)
  Automatic adjustment of driving level from 15 km/h

  air suspension unit with low-maintenance 430 mm disc brake axles
  3 x 9 t rigid, wheelbase 2 x 1,310 mm

  Tyres :
  6 x 385/65 R 22.5 160J, manufacturer as per factory specifications
  6 steel wheel rims 11.75 x 22.5, 10-hole, 120 mm rim offset, silver

  SUPPORT FIXTURES

  Mechan. 2 x 12 t support jacks, single-sided operation and thrust compensation, manufacturer as per factory specifications

  BRAKE SYSTEM

  Brake system according to EC Directive 71/320 or E CE R13
  Two-line brake
  EBS – electronic brake system
  Wabco 2S2M = one axle sensed
  RSS – stability program
  Spring-loaded parking brake on 2 axles
  Aluminium air tank

  FLOOR

  Resin-coated plywood floor, 27 mm, flush with external frame
  2 steel top-hat rails over the longitudinal beams, in front of the coil trough
  (floor load capacity 5,460 kg stacker axle load according to CSC)

  ELECTRICAL EQUIPMENT

  24 V lighting system according to EC Directive 76/756/E WG
  2 seven-chamber tail lights in underride protection
  LED side marker lights
  2 clearance lamps
  2 contour lights on underride protection
  2 x 7-pin and 1 x 15-pin socket

  PAINTWORK

  Blasted with steel granulate, treated with zinc dust primer and spray painted with 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

  Plastic and hot-dip galvanised parts unpainted,
  powder-coated attachments/installation parts black

  Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48

  ACCESSORIES

  Rear markings as per ECE standards (horizontal on rear doors/rear wall)

  ATTACHMENTS

  Rear crash guard with portal post protection and lower post reinforcement
  Wheel chock(s) as per regulations
  1 x retractable step unit at rear right
  Single wheel plastic mudguards with spray protection as per regulations
  Aluminium tarpaulin mounting strips bolted on both sides of external frame
  Aluminium underride protection, coated white
  Side impact protection made from aluminium profiles as per regulations, coated black
  1 spare wheel bracket for 1 spare wheel (rear right)
  1 plastic toolbox, lockable, unpainted , on left after axle

  SIDE WALLS/SLIDING TARPAULIN

  Fixed aluminium hollow profile front wall, 2,400 mm, with 2 centre supports, 2 lashing rings inside for load securing
  Closed with tarpaulin over front wall, in same colour as side tarpaulin
  Front wall reinforced inside with galvanised steel plate, approx. 650 mm high

  Plastic sliding tarpaulins on both sides with load certification according to Code XL; welded horizontal and vertical strap reinforcements incl. turnbuckles as well as front and rear bolt locks, openable on all 4 corners, with ratchet tensioner at rear,
  tarpaulin sealed against external frame,
  tarpaulin manufacturer as per factory specifications, tarpaulin colour according to availability
  Aramid-reinforced plastic roof tarpaulin, translucent

  Bolted portal at rear with aluminium corner posts, upper crossbeam with forward-sliding cover, incl. fully opening double door in profile design covering entire load space height, each leaf equipped with 2 internal espagnolettes

  COIL RECESS

  Useful length: approx. 7,400 mm – standard version according to VDI 2700 for coil diameters of 900 to max. 2,100 mm,
  with stacker-bearing cover made from 27 mm resin-coated plywood with trussing
  5 pairs of racks = 1 x at front, 1 x approx. 1,840 mm (before centre of gravity), 1 x 2,520 mm, 1 x 3,680 mm, 1 x 5,330 mm,
  incl. 2 pairs of steel tubular safety supports, 8 0 x 8 0 x 5 mm, useful height: approx. 1,700 mm
  Inclinations on both sides made from 24 mm resin-coated plywood

  POSTS/COVER

  2 fixed aluminium corner posts at front, bolted, protruding from sides
  3 centre posts on left in direction of travel, movable across entire length
  3 centre posts on right in direction of travel, movable across entire length
  4 rows of slat pockets, 1st pocket row at bottom 460 mm, spacing approx. 160/450/450 mm, with just 3 rows of aluminium pointed slats 100/25 mm

  Versus sliding cover with plastic brackets, forward-sliding with automatic elevation, limited backward movement (opened from above) = pushed together in loading area, with vertical and horizontal guide rollers = smooth operation
  Aluminium guide rail profile on both sides for sliding tarpaulins and posts, design height 140 mm
  Control rod for sliding tarpaulin (bracket on interior side protection)