SM trailers - Official importer of Schwarzmueller for Bulgaria,
Greece and Northern Macedonia.
SM trailers - Official importer of Schwarzmueller for Bulgaria,
Greece and Northern Macedonia.
3-AXLE LIGHTWEIGHT PLATFORM SEMITRAILER – COIL – INCLINED LOADER
Internal platform length: approx. 13,620 mm
Internal platform width: approx. 2,480 mm
Load space internal height: approx. 2,700 mm
Lateral loading height: approx. 2,640 mm
Rear loading height: approx. 2,700 mm
Loading height: approx. 140 mm over fifth-wheel height
Welded steel frame construction – lightweight design
Reinforced for point loading = coil transport (27 t at centre of gravity across min. 2,000 mm length)
Frame for unladen fifth-wheel height of 1,120 – 1,220 mm
Replaceable 2″ kingpin (EC installation dimension, width across corners: 2,040 mm)
23 pairs of recessed 2.5 t lashing points according to UVV, plus
6 pairs of 4 t lashing points in recess area on external frame
Air suspension with lifting and lowering device (approx. +120/-80 mm)
Automatic adjustment of driving level from 15 km/h
Air suspension unit with low-maintenance disc brake axles, ø 430 mm, 3 x 9 t rigid, wheelbase 2 x 1,310 mm
Autom. lifting front axle = raised or lowered according to weight (with the lifting axle raised, the loading height or total height increases by approx. 50 mm)
When the 1st axle is raised, the vehicle does not follow the legal turning circle
Tyres :
6 x 385/55 R 22.5 160J, manufacturer as per factory specifications
6 steel wheel rims 11.75 x 22.5, 10-hole, 120 mm rim offset, silver
Mechan. 2 x 12 t support jacks, single-sided operation and thrust compensation
Brake system according to EC Directive 71/320 or ECE R13
EBS – electronic brake system
Wabco 2S2M = one axle sensed
RSS – stability program
Spring-loaded parking brake on 2 axles
Aluminium air tank
Resin-coated plywood floor, 27 + 12 mm or 30 + 12 mm, flush with external frame
(floor load capacity: 5,460 kg stacker axle load acc. to CSC)
Fixed aluminium hollow profile front wall, 2,000 mm, with 2 centre supports,
2 lashing rings inside for load securing
Inside of front wall reinforced with aluminium chequer plate, 3/5 mm, up to a height of 600 mm
4-part aluminium hollow profile side walls, 600/25 mm, with vertical and horizontal rubber seal, incl. 2 bracket recesses, spacing of bracket rows approx. 280 mm, lower row with standard tarpaulin brackets, max. 200 mm spacing, customs-compliant, upper row with standard tarpaulin brackets, max. 200 mm spacing, not customs-compliant in this case, foldable with Kinnegrip single locking
Foldable aluminium hollow profile rear wall, 600 mm high, with vertical and horizontal rubber seal, incl. 2 bracket recesses, tarpaulin brackets and spacing as for side walls,
foldable with Kinnegrip single locking
1 folding step
Integrated extended lever locks, Kinnegrip system K20 with single locking
2 front corner posts, bolted, protruding from sides, in roof height
6 foldable Kinnegrip centre posts, split
2 rear Kinnegrip corner posts, foldable, side-mounted
5 rows of softwood slot-in slats, 100/27 mm, in pockets, spacing:
1 x 400 mm, then 200 mm
Edscha sliding tarpaulin frame, forward-sliding = pushed together
in loading area, without inclination, design height 95 mm, guide rail at front with extra division with spline end
Collapsed Edscha cover, hydraulically foldable against inside of front wall, folding down only possible in lowest cover position,
operation via pump unit on trailer (hydraulic cylinder and support protrude into loading area at the top when loading from the side)
Roof rack supports suitable for adjustable cover with unladen total height of 4,300 mm with bore holes and linchpins
Tarpaulin made from high-strength Trevira fabric with translucent roof, without side separation, incl. tarpaulin rope and assembly,
tarpaulin manufacturer as per factory specifications
24 V lighting system according to EC Directive 76/756/EWG
2 seven-chamber tail lights in underride protection
LED side marker lights
2 clearance lamps
2 contour lights on underride protection
2 x 7-pin and 1 x 15-pin socket
1 rear 2-pin socket in underride protection
Blasted with steel granulate, treated with zinc dust primer and spray painted with 2-component acrylic paints for commercial vehicles
Rear markings as per ECE standards
Rear crash guard with corner post protection
Wheel chock(s) as per regulations
Single wheel plastic mudguards with spray protection as per regulations
Aluminium underride protection, coated white
Side impact protection made from aluminium profiles as per regulations
1 spare wheel bracket for 1 spare wheel (rear right)
1 plastic toolbox, lockable, unpainted, on left after axle
Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48
Special configuration with hydraulic inclined loading for transporting
large format plates. Loading and unloading of plates even in horizontal position, i.e. raising with full load weight = 4 recessed transverse
tubular supports in floor, extendible, with hydraulic 4-stage lifting cylinder (individual actuation of each hydraulic cylinder), sealed from below with brush seal (splash water protection), with additional tubular safety supports and connecting rods
In each case 5 round pipe bushings at bottom + slot-in retainers made from 50 mm round steel, approx. 300 mm high
Plus one slot-in, height-adjustable tubular post at both front and rear
with diagonal support in neck area and at rear
Electrohydraulic operation with pump unit incl. separate steel plate oil tank,
2-battery power supply incl. storage box on trailer and charging cable up to front of trailer
Battery switch on equipment bracket at front, mounted on right in direction in travel
2 recesses in external frame on left in direction of travel for transporting round plates
4 round pipe bushings for slot-in retaining posts on left in direction of travel on external frame
4 resin-coated plywood panels, 400 x 400 x 40 mm, as base for inclined plate loading
Perforated steel rail recessed in floor up to first tubular support at front left in direction of travel, incl. 1 load securing wedge for front stop
Useful length: approx. 8,000 mm – special version for coil ø of 900 to max. 2,100 mm, 2 divisions in area of diagonal load beams,
with stacker-bearing cover made from 40 mm resin-coated plywood with tubular supports
5 pairs of racks = 1 x front, 1 x approx. 1,840 mm (before centre of gravity), 1 x 2,520 mm, 1 x 3,680 mm, 1 x 5,330 mm
incl. 2 pairs of tubular safety supports, 90 x 90 x 4 mm, useful height: approx. 1,700 mm
Inclinations on both sides made from 24 mm resin-coated plywood
Contact your preferred office and we will do our best to solve all your challenges
Get intouch
Всички права запазени. © 2024 SM Trailers | Bulgaria
Web Design Bulgaria - Dankanic Creative