3-AXLE LARGE-SCALE ALUMINIUM TIPPER SEMITRAILER
Special version with left-sided and rearward loading/unloading and tipping – for easily sliding bulk goods
Tipper body internal dimensions: approx. 10,500/2,450/1,945 mm = approx. 50 m³ load volume – or 26 pallet spaces
Total width: 2,550 mm
Total height, unladen: approx. 3,550 mm
for/over fifth-wheel height of 1,200 mm and 100 mm roof pitch
Loading height, unladen: approx. 320 mm over fifth-wheel coupling
For air-sprung 2-axle tractor
Naxtra welded steel frame construction – low body height
Replaceable 2″ kingpin
Air suspension with autom. lowering device via inductive switch and lowering lock via rotary switch on semitrailer
Additional raising and lowering
Air suspension unit with 430 mm disc brakes
3 x 9 t, rigid, wheelbase 2 x 1,310 mm
Autom. lifting front axle = raised or lowered according to weight (loading or total height increases by approx. 50 mm) and with forced lowering incl. integrated speed-restricted moving-off aid with button operation in cab
Tyres :
6 x 385/65 R 22.5 160J, manufacturer as per factory specifications
6 steel wheel rims 11.75 x 22.5, 10-hole, 120 mm rim offset, silver
Mech. 24 t support jacks with single-sided operation, low-maintenance
Brake system according to EC Directive 71/320 or ECE R13
Two-line brake
Spring-loaded parking brake on 2 axles
EBS – electronic brake system
Wabco 2S2M = one axle sensed
RSS – stability program
Steel air tank
1 central special tipper cylinder for side and rearward tipping,
rearward tipping angle: approx. 45°
1-pipe system with plug-in coupling DN 20
Aluminium corner body in pallet design = smooth inside and outside,
side walls, on right in direction of travel, and rear wall made from 30/4/2 mm hollow profiles with upper stabilising frame and 3 central, removable or foldable tubular crosspieces = also act as tarpaulin support, approx. 100 mm inclination (before opening out the door leaves, the front and rear transverse supports must be removed), uniform support over front wall = fixed and removable over rear wall
Special configuration on left side with 2-part main or attachment walls
Main walls made from reinforced tipper hollow profile, 40/4/2 mm, approx. 1,200 mm high, foldable with extended swivel bolt locks and 1 row of flat bolt locks
Hinged with electropneumatic central locking – control switch etc. must
already be installed in cab
Individually opening side walls with emergency switch on trailer
Spring lifting aids for main walls
2 tension chains with removable fasteners on both front and rear main wall plus diagonal tension chains and fasteners on centre posts
Attachment walls above, approx. 755 mm, openable as door leaves = mounted on corner posts with at least 3 hinges (before opening out the door leaves, the front and rear transverse supports must be removed), openable via press lock on centre posts
1 foldable and removable centre post on left in direction of travel, in attachment wall height
Material-tight side wall assembly = each wall with labyrinth sealing system
8 mm floor panels throughout, with narrow cross ribs
12 pairs of recessed lashing rings now moved slightly inward
5 mm front wall with reinforcements, without excavator protection
Combination front wall = fully opening 1-leaf door, mounted on right in direction of travel, hinged with autom. pneumatic locking incl. 1 central grain feeder with dosing lever and water guard plate, instead of double door
1 discharge funnel, approx. 300 mm long, incl. bracket on standing platform.
Front and rear walls vertical = pallet transport
Standing platform at front comprising aluminium safety grid with railing and step unit as well as step unit inside
3 removable stop brackets for roller tarpaulin on right
Plastic tarpaulin, manufacturer as per our specifications,
colour as per customer request
rolls up from left to right in direction of travel,
incl. aluminium slat and hand crank,
Side wall overhang approx. 400 mm on right side in direction of travel,
approx. 200 mm on left side, for main walls,
3 integrated aluminium tubes, 35 mm ø, resting on roof arches
4 tension belts on left incl. rubber pads as well as
turnbuckles on underside of body,
tarpaulin hooks at front for zig-zag lashing,
horizontal tarpaulin bracket rope fastening on right,
hooks at rear for zig-zag lashing at top of cross member
24 V lighting system according to EC Directive 76/756/EWG
2 seven-chamber tail lights
LED side marker lights
2 clearance lamps
2 contour lights
2 x 7-pin and 1 x 15-pin socket
Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)
Unpainted – cleaned = complete body
(corrosion marks on untreated aluminium surfaces due to road salt cannot be excluded)
Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black
Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48
Rear markings as per ECE standards
Wheel chock(s) as per regulations
Noise dampers = rubber pads
Foldable aluminium trapezoidal underride protection, unpainted
Single wheel plastic mudguards with spray protection as per regulations
1 spare wheel bracket for 1 spare wheel
Side impact protection
1 aluminium ladder, approx. 3 m long incl. bracket
1 integrated level gauge (to check horizontal position)
Operating rod for rear crossbeam incl. bracket
Contact your preferred office and we will do our best to solve all your challenges
Get intouch