3-AXLE 3-WAY TIPPER SEMITRAILER – LONG-HAUL TRANSPORT
For pallet and grain transport etc.
Internal length: approx. 13,400 mm
Internal width: approx. 2,460 mm
Internal height: approx. 2,200 – 2,400 mm
Total width: 2,550 mm
Total height, unladen: approx. 3,800 – 4,000 mm
Loading height: approx. 325 mm over fifth-wheel height
Naxtra welded steel frame construction – low design height
Connector lock for tipper body with cross-over protection
Replaceable 2″ kingpin
Air suspension with autom. lowering device via inductive switch and lowering lock via rotary switch on semitrailer
air suspension unit with low-maintenance 430 mm disc brake axles, 3 x 9 t rigid, wheelbase 2 x 1,310 mm
Tyres :
6 x 385/65 R 22.5 160J, manufacturer as per factory specifications
6 steel wheel rims 11.75 x 22.5, 10-hole, with rim offset, silver
Mechan. 24 t support jacks with single-sided operation, low-maintenance
Brake system according to EC Directive 71/320 or E CE R13
Two-line brake
Spring-loaded parking brake on 2 axles
EBS – electronic brake system
Wabco 2S2M = one axle sensed
RSS – stability program
Steel air tank
2 special tipper cylinders for 3-way tipping, installed in series
1 arrester cable
Rearward tipping angle: approx. 34°
1 pipe system with screw coupling DN20
24 V lighting system according to EC Directive 76/756/ EWG
2 seven-chamber tail lights in underride protection
LED side marker lights
2 clearance lamps
2 contour lights
2 x 7-pin / 1 x 15-pin socket
Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)
Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black
Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48
Wheel chock(s) as per regulations
Noise dampers
Single wheel plastic mudguards with spray protection as per regulations
Side impact protection
Aluminium underride protection, coated white
1 spare wheel bracket for 1 spare wheel
1 integrated level gauge (to check horizontal position during rearward tipping)
Gross train weight (perm.): 40 t
Gross weight (techn.): 39 t
Axle assembly load (techn.): 27 t
Fifth-wheel load (techn.): 12 t
Payload: approx. 25 t
Tare weight: approx. 8, 9 t
Full-steel welded construction with fine-grained special steel floor panels, 5 mm
(slight floor unevenness possible due to weld distortion)
Grain-tight side wall mounting with labyrinth sealing system
Fixed steel plate front wall, 3 mm, approx. 1,700 mm high
3-part reinforced aluminium hollow profile side walls, 40 mm, approx. 780 mm high, (top and bottom profiles reinforced 4/2 mm, 2 x 200 mm intermediate profiles 2/2 mm), with vertical special sealing groove and bracket recess for tarpaulin overhang (360 mm), without tarpaulin brackets, foldable with extended swivel bolt locks and hinged with man. central locking (operated separately for each wall)
Aluminium hollow profile rear wall, 40 mm, approx. 780 mm high, foldable with extended swivel bolt locks and hinged with man. central locking
2 fixed front corner posts, integrated in front wall, 2,000 mm high
4 foldable centre posts, 2,000 mm high (split approx. at side wall height,
lower section foldable, upper section removable with roof rack support)
Tension chain with fastener for centre posts
2 fixed rear corner posts, 2,000 mm high, welded to sides
4 rows of softwood slot-in slats, 100/27 mm, in pockets, 200 mm spacing
1 slat at front
Tarpaulin bows with 7 rows of roof poles and transverse bows for pillars, without inclination
(crane and stacker loading)
Rear markings as per ECE standards
Contact your preferred office and we will do our best to solve all your challenges
Get intouch