2-axle low-loader trailer with offset platform

• Product details

  TYPE DESIGNATION

  3-AXLE LOW LOADER TRAILER WITH WHEEL RECESSES FOR TRANSPORTING CONSTRUCTION MACHINERY

  FRAME

  Welded steel construction with flat front frame offset or body offset and drive-on taper at rear with externally welded square ribs
  4 pairs of mounting pockets for 80 x 40 mm tubular posts in external frame
  Recess in access slope for excavator shovel linkage
  3 pairs of lashing points in external frame
  5 pairs of recessed 5 t lashing rings in floor

  2 pairs of wheel recesses behind front offset with aluminium covers,
  approx. 1,150 mm long at bottom and approx. 535 mm long at rear between 2nd and 3rd axles, front wheel recess approx. 270 mm deep and rear recess approx. 220 mm deep.

  CHASSIS

  Reinforced, maintenance-free parabolic springs

  Low-loader axles, each with 11 t axle load
  S-cam brake 300/200 mm, autom. brake linkage adjuster
  Dual-axle compensation

  Tyres :
  12 x 245/70 R 17.5 143J, manufacturer as per factory specifications
  12 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver ex-works

  BRAKE SYSTEM

  Brake system according to EC Directive 71/320 or ECE R13
  Two-line brake
  EBS – electronic brake system
  Wabco 4S3M = 1st and 2nd axles sensed
  Spring-loaded parking brake on 2nd and 3rd axles
  Steel air tank

  FLOOR

  Softwood floor 50 mm, waterproofed, protruding approx. 5 – 10 mm beyond frame profiles or beyond steel stud plate cover over rear wheels

  EXTENSION

  Foldable = pivoting extensions, on both sides of drop deck and rear
  taper incl. continuous wooden boarding = also floor boards
  between side members when used without extensions (however, track width of construction machines/vehicles to be transported must not exceed the external frame width of 2,550 mm)
  2 removable warning signs at both front and rear
  Position and marker lights extendible to 3,000 mm

  RAMPS

  2 foldable, 1-part loading ramps, approx. 2,700/700 mm, with hardwood flooring and with externally welded square ribs
  Ramp width manually adjustable by approx. 550 mm, with rod,
  (min. spacing approx. 295 mm up to max. total width of 2,815 mm)
  lockable in driving position using chains with turnbuckle
  2 autom. folding supports at rear

  ELECTRICAL EQUIPMENT

  24 V lighting system according to EC Directive 76/756/EWG
  2 five-chamber LED tail lights on ramps
  LED side marker lights
  2 position or contour lights in each case, extendible to 3,000 mm
  Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector
  Bracket incl. revolving beacon on left ramp, with connecting cable and
  socket on end plate

  PAINTWORK

  Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles
  Plastic and hot-dip galvanised parts (extensions etc.) unpainted,
  powder-coated attachments/installation parts and drawbar black

  ACCESSORIES

  Rear markings as per ECE standards

  ATTACHMENTS

  Wheel chock(s) as per regulations
  Plastic mudguards or splashguards with spray protection as per regulations
  Side impact protection
  Spare wheel well for 1 spare wheel
  1 accessory compartment at front centre of raised platform, with folding lid
  Externally welded square ribs on ramps and rear access slope
  Centre of gravity marking
  Brackets for extension planks on frame

  BRIDGE PLATFORM

  Approx. 2,100/2,550 mm = raised platform at front incl. frame offset, tapered corners
  Approx. 5,500 or 6,100/2,550 mm = drop-deck platform – flat load surface or external surfaces advanced
  Approx. 1,010/2,550 mm = rear access slope
  Total width: approx. 2,550 mm or approx. 3,000 mm with extension
  Loading height, unladen: approx. 940 mm

  CONTOUR MARKINGS

  Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48

  DRAWGEAR

  Fixed drawbar, 1,800 mm long, 40 mm drawbar eye, 5° angle,
  with silent bushing